Top 10 Tips for Water Heater Maintenance and Installation

 A water heater necessitates as much care like any other electronic device. Despite the manufacturers offering the best parts that can handle relentless heating and cooling, you must remember that even the best parts will depreciate under constant pressure without proper heating maintenance in California.  

 

Let’s look at few tips for water heater maintenance and installation to extend its life despite the frequent expansion and contraction from heating and cooling. 

 

Points to Remember While Installing Water Heater  

 

1. Space Around the Device: 

 

If you install a water heater, keep some space between the apparatus and the walls. If the technician does not have sufficient wriggle room to check out the water heater parts, they cannot service it or repair it properly.  

 

It must be easily accessible if you wish to repair it or get it serviced. It is much better to put it on a portion of the wall that has nothing below the device and is away from damp areas like the shower, bathtub, or loo. This way, anyone can easily access it with a ladder during heating repair in California. 

 

2. Place the Water Heater at a Sufficient Height: 

 

You must install the apparatus at a height of a minimum of 1.8 meters or 6 feet from the floor. This ensures that the water pressure is enough and you avail of strong hot water flow in your tap instead of a trickle. 

 

3. Electrical Connections & Switches: 

 

Check if the apparatus is connected to a Miniature Circuit Breaker (MCB) that snaps electricity during power fluctuations. This will reduce the possibility of any short circuit in the water heater. Keep the switch away at a sufficient height from small children. It shouldn’t be too high that adults face problems while trying to reach it. 

 

 Maintenance Tips for Water Heater 

 

4. Never Keep the Heater Switched on for Prolonged Duration 

 

Many people keep the heater switched on for prolonged periods, particularly 
during the morning.  Everyone seeks warm water before they rush for work or school. They believe keeping the device on will save time. Today’s heaters heat the water within 5 minutes. Keeping the heater on for prolonged periods will lessen the life of the apparatus. Unnecessarily, no one wants a heating replacement in California. 

 

5. Save Electricity by Reducing the Temperature 

 

Water heater maintenance has its significance as you can save electricity too.  If you apply a lower temperature setting as the water will reach that temperature faster. The decreased temperature suggests the device will have to work less and this will extend its life. Additionally, warm water instead of very hot water in the tap will minimize the possibility of any accidental burns. Reducing the thermostat is particularly important for families with small children.   

 

6. Check the Anode Rod Inside the Tank Before Winter 

 

Larger heaters have an anti-corrosion anode rod within the tank. The rod attracts rust and other impurities in the water, thereby resisting the tank from becoming rusted or corroded. But, due to this, it corrodes away every few years. 

 

The rod also needs to be replaced if coated with whitish calcium sediments or its thickness has reduced drastically to below half an inch.  

 

7. Check the Pressure Release Valve 

 

Check at least annually whether the temperature and pressure release valves are functioning. You too can assess this by releasing the pressure a couple of times. It is a major concern if the relief valve at the water heater is leaking.  

 

8. Monitor the Plug 

 

Power fluctuations and applying low-capacity wiring for the power socket suggest that your switch will make a spark now and then. You will observe burn marks too on your plug’s pins as the higher electricity wattage will heat the plug and the pins and leave burnt traces. 

To avoid any further electrical short circuits from this, it is always advisable to employ new plugs and sockets and ensure that they are properly wired and plugged in.  

 

 9. Replace the Plastic Pipes with Metal Ones 

 

It is advisable to employ metal inlet and outlet pipes as they are more resistant to heat rather than the standard plastic ones you receive with a heater. Do not forget to check the joints frequently. If you observe whitish deposits from hard water or rust around the joints, then it is time to replace the inlet or outlet pipe.  

 

10. Don’t Ignore Annual Maintenance 

 

If you are inexperienced in maintenance work on a heater and wish to avoid water heater problems, then it is better to book an expert who is a thorough professional and will help with cleaning your water heater too. 

 

Always remember that when you buy a water heater, you are investing in it. It is like an asset that needs to be maintained. That’s why you need to maintain them properly so that they can run for years.